NOTICE: Ref: 456**NEW** Build your Own Custom Kit using our new Kit Builder... HEREFor a guide to using peltiers and avoiding condensation etc, please see the following thread in our forums. » Pelts - What they are and how to use them (Opens in New Window)
Swiftech MCW60-T Ref: 436The MCW60-T is a fully assembled liquid-cooled thermoelectric (Peltier) solution, specifically designed for high-end graphics processor. Operating temperature ranges from ambient to freezing levels, depending on the heat load, and thermal capacity of the liquid cooling system.This unit is intended for advanced users and requires appropriate insulation to prevent the formation of condensation in sensitive areas of the graphics card. Whereas Swiftech provides gaskets, and specific installation instructions for such assembly, utilization of this device is at the sole risk of the user.The MCW60-T features a 188 Watts built-in thermoelectric module that can be operated from 12 to 19 Volts and yields sufficient cooling power to operate most high-end GPU's from freezing to well below ambient temperature levels.The following curves describe the device behavior at various voltages and heat loads. Coolant temperature was maintained at a 35°C constant temperature,a value representative of what is attainable with current high-end liquid cooling kits (such as our H20-220 Apex Ultra for exemple):DOES NOT INCLUDE RAMSINKS! » Click Here for More Info (Opens in New Window) Price: £69.70 exc VAT (£81.90 Including VAT at 17.5%)
DangerDen Maze4-1 (1/2") - AMD SocketA TEC Block Lucite Top Ref: 632
DangerDen Maze4-1 (1/2") - Intel 775 TEC Block Lucite Top Ref: 634
DangerDen Maze4-1 (1/2") - A64 s754/939/940 TEC Block Ref: 637
DangerDen Maze4-1 Acetal Top GPU Block KIT (1/2" - Includes Foam & Pelt) Ref: 44
MeanWell s320-12 TEC PSU Ref: 293Output: 12Volts, 25Amps Switching PSUCurrent Range 0-25A215mm x 115mm x 50mm (8.47"x4.53"x1.97")Perfect for the 226W PeltWill Fit in Drive Bay but requires you to find your own way to mount it there... » Click Here for Manufacturer Specs (Opens in New Window) Price: £73.36 exc VAT (£86.20 Including VAT at 17.5%)
Neoprene Foam Pack Ref: 302A selection pack of varying thickness sheets of Neoprene for use in condensation sealing situations.One pack contains enough to seal your CPU TEC and GPU TEC... 5x 5x5" Sheets in the following thicknesses
Replacement Coldplate Bolts (Maze4-1 CPU) Ref: 993Pack of 4 bolts for the Maze4-1 CPU TEC Block Coldplate Price: £1.29 exc VAT (£1.52 Including VAT at 17.5%)
Replacement Coldplate Bolts (Maze4-1 GPU) Ref: 994Pack of 4 bolts for the Maze4-1 CPU TEC Block Coldplate Price: £1.29 exc VAT (£1.52 Including VAT at 17.5%)
PreCut Gasket for Maze4GPU-1 Ref: 524Precut foam gasket to match the Maze4GPU-1 Pelt GPU Waterblock. Price: £6.99 exc VAT (£8.21 Including VAT at 17.5%)
PreCut Gasket for Maze4-1 Ref: 525Precut foam gasket to match the Maze4-1 Pelt CPU Waterblock. Price: £5.78 exc VAT (£6.79 Including VAT at 17.5%)
Luberex Dielectric Grease 59ml Ref: 61
Dow Corning DC4 Dielectric Grease (100g) Ref: 950Designed to exclude moisture from terminal connections of aircraft ignition systems. More water repellent than paraffin or waxes. Temp. range -70° to 400° F. A low loss dielectric. 5.3 oz. tube. Price: £8.29 exc VAT (£9.74 Including VAT at 17.5%)
Copper Cold Plate for Maze3 CPU Ref: 429ColdPlate Kit to upgrade Maze3 to Maze3-1. Includes 4x Mounting Screws. Price: £12.99 exc VAT (£15.26 Including VAT at 17.5%)
Copper Cold Plate for Maze4 CPU Ref: 736ColdPlate Kit to upgrade Maze4 to Maze4-1. Includes 4x Mounting Screws. Price: £8.66 exc VAT (£10.18 Including VAT at 17.5%)
80w Peltier (Potted) Ref: 218WE CANNOT BE HELD RESPONSIBLE FOR ANY DAMAGE THIS PRODUCT MAY CAUSE TO YOUR SYSTEM.Potted Peltier rated @ 80W 8A 14.4V. Comes without Molex Connector, and should be used on any power supply with a rating of 12V and 8A or more. PLEASE NOTE: IF THIS DEVICE IS USED WITH A POWER SUPPLY RATED UNDER 8A, FAILURE OR DAMAGE MAY OCCUR WITH THE POWER SUPPLY AND OR OTHER COMPONENETS! !! POTTED=EDGES SEALED WITH EPOXY FOR MOISTURE PROTECTION 80W Potted Peltier (TEC). Qmax=80W, Imax=10A, Tmax=68C, Vmax=15.8V, Size=40x40x4.8mm. Fitted with molex HDD style power connector. Potted = Sealed for moisture protection Price: £14.68 exc VAT (£17.25 Including VAT at 17.5%)
172w DRIFT 0.8 Peltier (Potted) Ref: 770WE CANNOT BE HELD RESPONSIBLE FOR ANY DAMAGE THIS PRODUCT MAY CAUSE TO YOUR SYSTEM.Potted Peltier rated @ 172W 11.3A 24.6V, Delta Tmax of 69 deg C. Comes without Molex Connector, and should be used on any power supply with a rating of 12V and 11A or more. PLEASE NOTE: IF THIS DEVICE IS USED WITH A POWER SUPPLY RATED UNDER 11A, FAILURE OR DAMAGE MAY OCCUR WITH THE POWER SUPPLY AND OR OTHER COMPONENETS! !! POTTED=EDGES SEALED WITH EPOXY FOR MOISTURE PROTECTION 172W Potted Peltier (TEC). Qmax=172W, Imax=11.3A, Tmax=69C, Vmax=24.6V, Size=40x40x3.2mm. Potted = Sealed for moisture protection Price: £23.56 exc VAT (£27.68 Including VAT at 17.5%)
226w Peltier (Potted) Ref: 167WE CANNOT BE HELD RESPONSIBLE FOR ANY DAMAGE THIS PRODUCT MAY CAUSE TO YOUR SYSTEM.Potted Peltier rated @ 220W 24A 15.5V. Comes without Molex Connector. Use on any power supply with a rating of 12V and 24A or more. PLEASE NOTE: IF THIS DEVICE IS USED WITH A POWER SUPPLY RATED UNDER 16A, FAILURE OR DAMAGE MAY OCCUR WITH THE POWER SUPPLY AND/OR OTHER COMPONENTS!!! 220WPotted Peltier (TEC). Qmax=220W, Imax=26A,Tmax=65c, Vmax=15.8v, Size=50x50x3.6mm. Potted = Sealed for moisture protection. Price: £23.24 exc VAT (£27.31 Including VAT at 17.5%)
Clearance Items
